Technical reading

How to Evaluate Solar Panel Manufacturers: A Procurement View from ACWA Power

Ask five people how to evaluate solar panel manufacturers and you'll get five different checklists. Some start with module efficiency. Some start with price per watt. A few start with whether the brand appears on the project lender's approved list. None of these is necessarily wrong, because the right answer depends on who is buying and who carries the risk when a solar panel fails.

I sit on the procurement side of that question at ACWA Power. I'm not a module test engineer, and I don't speak for every department. My job is to translate manufacturer claims into contracts. Over the past seven years, I have helped evaluate dozens of PV module suppliers for utility-scale plants and for a few photovoltaic module private label projects. If you search ACWA Power news today, you'll see project milestones and financial announcements. This is the quieter side of those projects: deciding whether a supplier should be signed at all.

Start with one question: Who pays when a module fails in year eight?

Every manufacturer can present a datasheet that looks good. The real difference appears when panels age. So before comparing test reports, answer one question: if a module fails in year eight, whose phone rings?

If an asset owner operates the plant for 20 years, failure means lost revenue. If an EPC builds and hands it over, failure means warranty claims and construction defects. If a distributor puts its own logo on modules, failure means customer calls and brand damage. Different owners, different risk profiles, different evaluation processes.

That is also why I hesitate to give one universal supplier checklist. A manufacturer can be right for one buyer and wrong for another.

The four scenarios I use when evaluating PV module suppliers

Scenario 1: You are a utility-scale IPP or asset owner

Let's start with the scenario I know best. ACWA Power does not make every PV module that goes into a plant. We buy from suppliers, often at gigawatt scale, then operate the plants for decades. Because the asset must be bankable for 25 years, procurement evaluation has to cover both product quality and supplier staying power.

For utility projects, I use three filters: accredited test reports, financial health, and factory audit behavior. The test reports should be based on IEC 61215 and IEC 61730 standards and come from a credible laboratory, not just from a sales folder. Financial health matters because a warranty from an insolvent manufacturer is a piece of paper. Factory audit behavior matters because the best quality data is often the data they do not want to show.

Ask to see the line rejection log. Ask what happens to modules that fail flash test. Ask for traceability of one serial number back to the cell and bill of materials. The answer tells you more than the latest press release.

The counterintuitive part for many buyers is that the lowest price often loses. I remember one tender where two suppliers were within $0.004 per watt. The lower quote came from a smaller factory with no in-region support history. The higher quote came from a supplier with local operations and long-term service reputation. We selected the higher quote. I don't have hard data proving the cheaper module would fail. I do know that the cheaper option would have added unnecessary risk to a 25-year revenue model.

Scenario 2: You are an EPC contractor

As an EPC, your time horizon is shorter. You care about completing the plant on schedule and avoiding rework. That means module evaluation should include physical compatibility and installation risk, not just nameplate watts.

A module can meet all datasheet specs and still slow down a project if the frame tolerance doesn't fit the mounting clamp or the connector brand doesn't match your design. I remember one EPC team that selected a module with slightly higher efficiency. They discovered later that the frame was a few millimeters wider than the mounting profile. It wasn't a fatal problem, but it cost about a week of adjustment across the site. That kind of problem is not captured by a flash test report.

My advice for EPCs is to build a shortlist of modules your crews have already installed and that have support in the region. All else equal, a proven module with fewer installation surprises is better than a slightly more efficient module nobody on the site has touched before.

Scenario 3: You are planning a photovoltaic module private label

Private label changes the nature of the decision. When a factory makes panels for you to sell under your own brand, you are no longer choosing a component. You are building a product that will carry your company's name for decades.

Your customer does not see the OEM. If the junction box fails in year two, the customer does not call the factory. They call you. If the factory quietly changed the encapsulant or cell supplier after your first order, you are still the one who must explain it. I have seen this pattern in the market: same-looking panel, different internal materials, weakened performance. The front label may not reveal it until the warranty claims start.

So for a serious photovoltaic module private label, evaluate the factory almost like a would-be partner. Demand transparency on the full bill of materials. Demand a contractual commitment that the manufacturer will not change cell, encapsulant, junction box, or connector suppliers without written approval. Demand access to production data and allow third-party inspections during production, not only after final assembly. A good factory welcomes these conditions because they protect both parties. A price-focused factory may resist. That resistance is your warning sign.

The added inspection cost may be one or two cents per watt. Perhaps less at higher volumes, though I don't have current market data for every factory. Whatever it costs, it is cheaper than discovering a bad batch after your brand is already installed.

Scenario 4: You are a smaller developer or first-time buyer

This scenario deserves more attention because it is where the cheapest mistake usually happens. If you buy only one to five megawatts a year, or if this is your first solar project, do not start a private label yet. Buy from an established manufacturer through an authorized distribution channel.

The fixed costs of a private label contract—new certifications, legal review, quality inspections, traceability systems, spare parts and after-sales processes—are almost the same whether you buy 1 MW or 100 MW. A low-priced, no-name module may save a small amount per watt upfront, but one problem batch can wipe out that saving several times over. I almost learned this early in my own career with a supplier that seemed good on paper; a colleague asked who would support the warranty if that factory disappeared. The right answer was not the one I wanted to hear.

How to know which scenario you are in

If you are still torn, ask three practical questions. Who still owns the asset ten years after commissioning? If you or your investor do, use scenario one. Does your company name appear on the module in front of the customer? If yes, add scenario three evaluation, even if you are an EPC. Is your annual volume low enough that you cannot absorb a recall or warranty dispute? If yes, scenario four wins.

Some situations overlap. A utility-scale IPP may want to control spare modules with its own label. An EPC may hold a few assets after settlement. When they overlap, I choose the stricter evaluation. A reliable supplier with financial strength and independent test data works in every scenario. A cheap supplier only looks good in the scenario that ignores long-term consequences.

What all scenarios share: TCO, not sticker price

At some point, every buyer has to compare prices. I still use a total cost of ownership model. The calculation includes module price, freight, import duties, financing cost, spare modules, degradation assumptions, inspection cost, and the administrative cost of handling warranty claims. I built this model after a mistake in my first year; now it is the first sheet I open.

Total cost of ownership is not complicated in principle. It is just unpopular because it gives no single number on a quote. A supplier may win on unit price and lose on total cost once callbacks, lower actual yields, and uncertain warranty support are included. The opposite is also possible. A premium product can be the cheapest total cost over 25 years.

Final word from ACWA Power procurement

If you came looking for ACWA Power news today, you know that the company is moving into more markets, more renewables, and more complex projects. On the ACWA Power official website, you can find financial reports, project announcements, and sustainability material. What you won't find there is the detailed evaluation process behind a module supplier decision. That work is not glamorous, but it is one of the reasons large solar plants keep producing electricity long after the ribbon-cutting ceremony.

There is no perfect solar panel manufacturer for everyone. There is only the manufacturer that fits your risk profile. So start with the right scenario, apply the cost test, and treat quality as a brand issue. The time to evaluate is before you sign, not after.

Renata Silva

Renata Silva

Renata Silva is a photovoltaic module analyst covering monocrystalline solar panels, bifacial modules, TOPCon and heterojunction designs, glass-glass construction, junction boxes, and module warranties. She interprets IEC 61215 and IEC 61730 evidence while comparing rated power, conversion efficiency, temperature coefficient, bifaciality, insulation, mechanical-load results, degradation assumptions, and tolerance. Her technical guides help EPC engineers, distributors, and project buyers separate qualification evidence from site-specific energy yield, climate exposure, installation constraints, and long-term performance risk.